Blueant V1 Manual de usuario descargar pdf

T1 Quick Start Guide: English

Vol - Vol +

Multi-

Function

Button

(MFB)

Microphones

Indicator

Light

Charging

Port

Charge Your T1

Your T1 has been given an initial partial charge to get

started, but for best results charge it using the supplied USB

cable and adaptor until the indicator light turns white.

> Charge the T1 whenever it announces that the battery is

Very Low.

> A full charge takes about 3 hours.

> During charging, the indicator light ﬂ ashes red.

> When the light goes white, the charge is complete.

Pair Your T1

1. Turn the T1 on by

sliding the power

switch on the back to

the green on position.

2. Put the T1 in your ear.

3. The ﬁ rst time you use the T1 it will go straight to pair

mode and talk you through the pairing process.

For subsequent pairings, make sure the T1 is not

connected to any phones, then hold down the MFB. The T1

will announce that it is going into pairing mode.

Tip: The pairing code is 0000 (four zeros).

Power switch (on)

Transfer Your Phonebook

Once the pairing is complete, your T1 will attempt to transfer

your phonebook contacts so that it can announce the names

of incoming callers. Please accept any connection requests

from the T1 and wait for the transfer to ﬁ nish.

Some phones do not support automatic phonebook

transfers. If the T1 announces that this is the case, you need

to go to your phone’s address book and send contacts via

Bluetooth to the T1. See www.blueantwireless.com for help.

Note: Whenever you add contacts to your phone in future

you must update your phonebook on the T1: with the T1

connected to your phone but not on a call, hold down the

MFB for 3 seconds to initiate a phonebook update.

Wearing the T1

You can wear your T1

on either ear.

For best results:

> Position the hook and

ear gel as shown here.

> Make sure the T1 is angled

towards your mouth.

Protective Skins

Your T1 is supplied with optional rubber

skins to protect against dust and

moisture.

RIGHT

EAR

LEFT

EAR

Making Calls

Use your voice to make calls:

1. Click the MFB and wait for the T1 to ask you

to Say A Command.

2. Say Phone Commands to activate the voice

dial feature on your phone (if supported by

your phone).

Or:

> Dial the number on your phone and the audio will

automatically transfer to the T1.

> Hold down Vol + for 1 second to redial the last outgoing

call.

Taking Calls

When the phone rings, you can answer the

call with your voice: wait for the prompt to ask

you if you want to take the call, and then say

Answer or Ignore.

If you don’t want to wait for the prompt, or you

are in a noisy place:

> Click the MFB once to accept the call.

> Double click the MFB to reject the call.

During a call, click the MFB to end the call.

Voice Commands

To use any of the voice commands, click the MFB, wait for

the T1 to ask you to Say A Command, then say the command:

> Check Battery — Tells you the battery level on the T1.

> Call Information — Calls an information service number

stored in your headset. Call charges may apply.

> Phone Commands — Activates your phone’s voice dialing

feature (if available on your phone). Depending on your

phone model, you may need to record voice tags on the

phone to use this feature.

Voice recognition will cancel automatically after a short

period of time if you do not say a command. You can also

cancel voice recognition by clicking the MFB.

Listening to Audio

The T1 supports A2DP audio streaming: if your phone or

Bluetooth device supports the A2DP proﬁ le then you can

simply start playing music or any other audio (including

directions from a GPS application on the phone) and it will

automatically transfer to the T1.

The audio will mute automatically if you make or receive a

phone call, and resume when the call ends.

Multipoint

Up to 2 phones can connect to the T1 at the same time. To

pair a second phone:

1. Use your phone’s Bluetooth menu to disconnect the

existing paired phone from the T1.

2. With the T1 switched on, hold down the MFB until the T1

starts to talk you through the pairing process.

3. When the pairing is complete, use the Bluetooth menu on

each phone to reconnect them to the T1.

When you have 2 phones connected, you can always answer

a call on either phone. If you initiate a call through the T1 it

will happen on the “primary phone”: the one that connected

to the T1 ﬁ rst.

Advanced Button Functions

> To hold an active call and switch to an incoming or held

call, press Vol + for about 1 second.

> To end an active call and answer a new incoming call,

press Vol - for about 1 second.

> You can conference two active calls together by holding

the MFB for 3 seconds (if your phone and network support

this).

> To transfer audio to the phone, click Vol + and Vol -

together during a call.

> To disconnect your phone from the T1, click Vol + and Vol-

together when you are not on a call. Hold down Vol + for

about 1 second to reconnect.

Advanced Button Functions

> During a call you can mute and unmute the T1 microphone

by holding Vol + and Vol - together until the T1 beeps twice

(about 1 second).

> Whenever you add contacts to your phone you must also

update your phonebook on the T1: with the T1 connected

to your phone but not on a call, hold down the MFB for 3

seconds to initiate a phonebook update.

> To turn the ﬂ ashing indicator light on or off, disconnect

the T1 from your phone and hold down Vol + and Vol - for

1 second.

> Click the MFB to: end a call, cancel pair mode, cancel voice

recognition, or cancel a phonebook transfer/update.

Upgrades

To enhance your experience, we are continually upgrading

the T1 ﬁ rmware.

From time to time we will make upgrades available on our

website for you to download and apply to your T1.

Go to www.blueantwireless.com for full details on the latest

upgrades available for your T1.

You must register your product online at

upgrades.

Reset your T1

If you are having problems with the T1, you can reset the T1

and your phone and start again:

1. Disconnect the T1 from your phone by deleting the pairing

from your phone’s Bluetooth menu.

2. Turn your phone off and back on again to clear its memory.

3. With the T1 switched on, but not connected to any phones,

click all three buttons (Vol +, Vol -, and the MFB) together.

The T1 will reset and go straight to pairing mode.

You will now need to pair your phone with the T1 again.

Help and Support

This guide is just to get you started with the T1. If you

are having trouble getting the T1 to work, please visit

www.blueantwireless.com for online help, support, and

troubleshooting tips.

Please call us before returning the T1 to a store and we will

help you through any difﬁ culty you may have.

> North America: 1866 891 3032

> Australia: 1300 669 049

> New Zealand: 0800 443 122

Terms and Conditions

By using this product you are agreeing to BlueAnt’s terms

and conditions, available at www.blueantwireless.com.

Warning: All BlueAnt devices are designed to reach volumes

of up to 100 decibels. Prolonged use at high volumes may

affect your hearing capacity. Using for extensive time periods

may result in noise induced hearing loss (NIHL). Please read

the enclosed safety card for information about the safe use

of BlueAnt products.

The Bluetooth

word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any use of

such marks by BlueAnt Wireless is under license.

Version: T1-QSG-AUEN-1.2

1 2

Indice de contenidos

Pagina 1 - Protective Skins

T1 Quick Start Guide: English1Vol - Vol + Multi-Function Button (MFB)MicrophonesIndicator LightChargingPort Charge Your T1Your T1 has b

Pagina 2 - Version: T1-TSG-AUEN-1.2

Troubleshooting Tips: EnglishThe following are some troubleshooting tips for using the T1 with speciﬁ c phone models.Phonebook TransfersWhen y

Mas documentos para No Blueant V1

a Ver el documento Blueant V1 Manual de inicio rápido

Blueant V1 Manual de inicio rápido (2 paginas)

Comentarios a estos manuales

Sin comentarios

Blueant V1 Manual de usuario

Busca en linea o descarga Manual de usuario para No Blueant V1. T1 Quick Start Guide: English Charge Your T1 Manual de usuario

Indice de contenidos

Mas documentos para No Blueant V1

Comentarios a estos manuales

Relacionado con productos y manuales para No Blueant V1